As we have progressed into manufacturing one of the largest ranges on supercharger components mainly for inline powered engines Aussiespeed has been forced into designing, testing and manufacturing our own supercharger drive systems. Our team has spent countless hours measuring, manufacturing jigs and fixtures as well as performing experiments and tests on components to deliver an Australian made supercharger drive system that can be used on both spline and pin and coupler type super chargers.
The outer drive of Aussiespeed supercharger drives can be painted, polished or left in a natural blasted aluminum finish.
With sand cast fully machined outer casing our supercharger internal shafts are cnc machined. We use steel supercharger hubs and steel supercharger pulleys over aluminum super charger hubs and aluminum supercharger pulleys. The hub uses a 3/8 unf threaded bolt, domed stainless steel retaining washer and 3/16 steel key into the drive end of the shaft. We do not rely on the bolts to locate the position of the pulley to the drive hub as it locates on the outer edge of the hub and the 4 x 6mm metric bolts simply attach the pulley to the hub.
When it comes to the part number on our Aussiespeed supercharger drive snouts this can be a little confusing so below are our standard part numbers the intended use they were designed for and the over all length. The part number refers to the actual super charger shaft length. Not the usable length from the supercharger gear case mounting face.
Spline Drive Snout Assemblies
This is the snout length when measured from the gear case mounting to the end of the Aussiespeed AS0487-24 supercharger steel 4 bolt hub without a pulley mounted to the snout.
Part number AS0480-166 = 161mm
Part number AS0480-182 = 177mm
Part number AS0480-209 = 204mm
Part number AS0480-224 = 219mm
Part number AS0480-247 = 242mm
Part number AS0480-267 = 262mm
Part number AS0480-290 = 285mm
The Aussiespeed supercharger top pulley mounts on to the AS0487-24, this is included when you buy a snout assembly and included in the usable length measurements.
If you are trying to work out what the length of the snout will be again measured from the supercharger front cover to the end of a 6 rib pulley you need to add another 30mm to the length.
An Aussiespeed 6 rib supercharger pulley over all is 30mm wide. It locates and recesses 2mm onto the AS0487-24 and adds 28mm to the length of the Aussiespeed super charger drive snout.
Aussiespeed splined snout with 6 rib pulley fitted
Part number AS0480-166 fitted with a 6 rib pulley = 189mm
Part number AS0480-182 fitted with a 6 rib pulley = 205mm
Part number AS0480-209 fitted with a 6 rib pulley = 232mm
Part number AS0480-224 fitted with a 6 rib pulley = 247mm
Part number AS0480-247 fitted with a 6 rib pulley = 270mm
Part number AS0480-267 fitted with a 6 rib pulley = 313mm
An Aussiespeed 10 rib supercharger pulley over all is 37.5mm wide. It locates and recesses 2mm onto the AS0487-24 and adds 35.5mm to the length of the Aussiespeed super charger drive snout.
Aussiespeed splined snout with 10 rib pulley fitted
Part number AS0480-166 fitted with a 6 rib pulley = 196.5mm
Part number AS0480-182 fitted with a 6 rib pulley = 212.5mm
Part number AS0480-209 fitted with a 6 rib pulley = 239.5mm
Part number AS0480-224 fitted with a 6 rib pulley = 254.5mm
Part number AS0480-247 fitted with a 6 rib pulley = 277.5mm
Part number AS0480-267 fitted with a 6 rib pulley = 320.5mm
WHAT SNOUT IS IN WHAT KIT.
Below is the listing of what snout part number goes with what engine and supercharger. This is remembering that the snout lengths and part numbers are to suit the positioning with either an Aussiespeed manifold and in some cases an Aussiespeed manifold and adapter plate and 6 rib pulley. Below is Spline Drive when used with our Aussiespeed 1 inch spline drive coupler.
Part number AS0480-166.
Holden 6 cylinder 192 TBS supercharger.
Part number AS0480-181
Slant 6 Chrysler 192 TBS supercharger
Part number AS0480-209
Holden 6 cylinder 142,144 Weiand Supercharger
Part number AS0480-224
Slant 6 Chrysler 142,144 Weiand supercharger
Hemi 245,265 192 TBS supercharger
Chev 250,292 with single balancer 192 TBS supercharger
Ford 200,250 Crossflow Non PS 192 TBS supercharger
Part number AS0480-247
Chevy 250,292 triple pulley 192 TBS supercharger
Ford 200,250 crossflow with power steering 192 TBS supercharger
Part number AS0480-267
Hemi 245,265 Weiand 142/144 supercharger
Chevy 250,292 with single crank pulley 142/144 Weiand supercharger
Ford 200,250 Non Power steering 142/144 Weiand supercharger
Part number AS0480-290
Chevy 250,292 triple pulley with 142/144 Weiand supercharger
Ford 200,250 Crossflow with power steering 142 Weiand supercharger
Below is a list of our 3 pin drive supercharger snouts. The snouts are designed to be used with our Aussiespeed M90 gearcase, manifold and manifold to supercharger adapter.
Holden 6 cylinder M90 Generation 5 Eaton supercharger.
Chrysler Slant 6 with generation 5 M90 Eaton supercharger
Chrysler 245,265 with generation 5 M90 Eaton supercharger
Chevrolet 250,292 with single crank pulley and generation 5 M90 Eaton supercharger
Ford 200,250 Crossflow 6 cylinder non power steering with generation 5 M90 Eaton supercharger
Chevy 250,292 with triple pulley with generation 5 M90 Eaton supercharger
Ford 200,250 Crossflow 6 cylinder with power steering with generation 5 M90 Eaton supercharger.
Aussiespeed have designed snout mounted offset tensioners, snout support kits to suit many different engines. To view our online store listing of our entire range of super charger drive components click the link below.